Lockout / Tagout
Control of hazardous energy — procedures, training, and periodic inspection.
Duration4 hrs
LevelSpecialized
VerticalGeneral Industry
29 CFR 1910.147
SECTION_00 // Resources / Safety & Compliance Knowledge Base
Safety & compliance resources for modern workplaces.
A working reference for EHS managers, contractors, and operations leaders who need to turn OSHA, NFPA, and ATSSA requirements into action. Use it to scope an audit, brief a crew, or prepare for an inspection.
SECTION_01 // Why this matters
Occupational safety compliance is not a single document — it is a living system built from hazard recognition, written programs, training records, and the discipline to keep all three current. For general industry, the controlling framework is 29 CFR 1910; for construction, 29 CFR 1926. Layered on top are consensus standards such as NFPA 70E for electrical safety and ATSSA flagger certification for temporary traffic control. Each standard answers a different question, but they share one goal: send every worker home in the same condition they arrived.
Most workplaces do not fail an inspection because they are careless. They fail because the standard is dense, the hazard is invisible, and the documentation lagged behind the work. A phased compliance audit closes that gap by mapping your actual operations against the applicable standard, ranking findings by risk, and producing a defensible corrective-action plan rather than a handed-off checklist. Pair that audit with on-site, instructor-led training and the compliance posture becomes cultural instead of ceremonial — your crew learns to recognize the hazard before it becomes an incident.
The resources below index the compliance focus areas we audit against and the certified courses we deliver on-site across Pennsylvania and Maryland. Each entry maps to a specific standard citation so you can trace a requirement back to its source. If you do not see your topic listed, contact us — we build site-specific programs for the hazards your facility actually faces.
SECTION_02 // Certified training catalog
On-site courses mapped to the standards.
NFPA 70E Electrical Safety
Arc flash and shock hazard analysis, energized work permits, and PPE category selection.
Duration8 hrs
LevelSpecialized
VerticalAll Industries
NFPA 70E
ATSSA Flagger Training
Work zone setup, signaling, and temporary traffic control per the MUTCD.
Duration4 hrs
LevelEntry
VerticalConstruction / Roadway
ATSSA / MUTCD
First-Aid / CPR / AED
Adult CPR, AED operation, and basic first-aid response — choking, bleeding control, and sudden illness emergencies.
Duration4-6 hrs
LevelEntry
VerticalAll Industries
ASHI / AHA Guidelines
Stop the Bleed
Life-threatening bleeding control — tourniquet application, wound packing, and the ABCs of bleeding per the national Stop the Bleed campaign.
Duration2 hrs
LevelEntry
VerticalAll Industries
Stop the Bleed / ACS
OSHA 10-Hour Outreach
Foundational awareness for workers on common hazards, rights, and employer responsibilities.
Duration10 hrs
LevelEntry
VerticalGeneral / Construction
29 CFR 1926 / 1910
OSHA 30-Hour Outreach
Deeper hazard recognition and supervisor-level responsibilities for crew leads and managers.
Duration30 hrs
LevelSupervisor
VerticalGeneral / Construction
29 CFR 1926 / 1910
Fall Protection
Systems, anchor points, inspection, and rescue planning for fall hazards.
Duration4 hrs
LevelSpecialized
VerticalConstruction
29 CFR 1926 Subpart M
Confined Space Entry
Permit-required spaces, atmospheric testing, attendants, and entry procedures.
Duration6 hrs
LevelSpecialized
VerticalGeneral Industry
29 CFR 1910.146
Hazard Communication
HazCom 2012 / GHS — SDS interpretation, labeling, and chemical safety programs.
Duration3 hrs
LevelEntry
VerticalAll Industries
29 CFR 1910.1200
SECTION_03 // Compliance focus areas
The standards we audit against.
General Industry
Walking-Working Surfaces
Slip, trip, and fall hazard control across floors, stairs, platforms, and elevated work surfaces under Subpart D, including guardrail, ladder, and anchorage requirements.
29 CFR 1910 Subpart D
Construction
Fall Protection Systems
Active and passive fall arrest, travel restraint, and guardrail systems for leading-edge and roof work, with rescue planning for suspended workers.
29 CFR 1926 Subpart M
Electrical
Electrical Safety & Arc Flash
Shock and arc flash hazard analysis, energized work permits, boundary calculations, and PPE category selection for qualified and unqualified workers.
NFPA 70E / 29 CFR 1910 Subpart S
General Industry
Lockout/Tagout (LOTO)
Control of hazardous energy for machine servicing and maintenance, including written procedures, periodic inspections, and authorized employee training.
29 CFR 1910.147
Transportation
Work Zone Traffic Control
Temporary traffic control plans, flagger positioning, and signing for roadway work zones, aligned to the Manual on Uniform Traffic Control Devices.
ATSSA / MUTCD Part 6
Emergency Response
Emergency Action Plans
Evacuation, shelter-in-place, and emergency response procedures, including alarm coverage, egress capacity, and employee role assignment.
29 CFR 1910.38
SECTION_04 // Engage
Need a resource tailored to your site?
We build site-specific compliance programs and deliver on-site training for the hazards your facility actually faces.
